The Bosch GBC18V-32PSN16X is a commercial-grade 18V cordless cold-cutting rebar cutter engineered to cut carbon steel reinforcing bar up to #10 (1-1/4 in. / 32 mm) diameter. Powered by a high-output brushless motor delivering the equivalent of 13 Amps of corded power, it provides rapid site cutting for concrete reinforcement, foundation construction, bridge infrastructure, and demolition work without gas generators or trailing extension cords.

Engineered with tungsten carbide-tipped (TCT) cold-cutting circular blade technology, the tool slices through #5 rebar in two seconds. Cold-cutting produces clean, virtually spark-free and burr-free cuts, significantly reducing hot-work hazards and eliminating edge discoloration associated with abrasive chop saws or torches. A full-enclosure blade guard and a release-to-stop safety paddle switch protect operators against accidental blade contact during high-speed shearing cycles.

Jobsite ergonomics are enhanced by a rotatable handle and a vibration-damped auxiliary side handle, allowing comfortable horizontal, vertical, and flush cutting in tight rebar grids. An intelligent user interface (HMI) provides speed selection tailored to bar diameters and live tool diagnostics for preventative maintenance.

Features & Benefits

• 13 Amp Corded Equivalent Power: High-performance brushless motor delivers heavy cutting force to slice up to #10 (1-1/4 in. / 32 mm) steel rebar.
• Rapid Cut Rate: Completes cuts through #5 rebar in two seconds to accelerate rebar tying and grid installation.
• Cold-Cutting TCT Technology: Uses tungsten carbide-tipped circular blades to generate minimal sparks, burr-free cut ends, and reduced heat buildup.
• Rotatable Main Handle: Rotates to optimize operator balance and control when cutting tied rebar at awkward angles or close to grade.
• Intelligent HMI Display: Provides speed adjustment and proactive tool status monitoring for motor protection and maintenance management.
• Enhanced Operator Safety: Equipped with an enclosed blade guard, fast-stopping blade brake, and responsive paddle switch.
• AMPShare Battery System: Fully compatible with Bosch 18V lithium-ion batteries and AMPShare partner platforms.

What's Included

• (1) GBC18V-32 18V Rebar Cutter
• (1) Anti-Vibration Auxiliary Handle
• (2) DCB530RC Rebar Cutter Blades
• (1) Carrying Case

Shipping: Beaver Industrial Supply offers free shipping on orders over $199, with the exception of Sawstop and Laguna, which require additional fees to be collected. Other exceptions apply as noted on product pages.

We reserve the right to determine the fastest and most cost-effective manner of transportation for all orders that qualify for free shipping. Our shipping carriers cannot deliver to PO box or U.S. military post office box addresses, such as APO and FPO, so we require a physical street address for delivery. We use USPS, which typically takes 2-8 days for delivery, depending on your location, for smaller items and UPS Ground for all other ground shipments under 150 pounds.

• Returns: We accept returns and exchanges for a fee up to 30 days in unopened, new, and unused condition in the original packaging. Exceptions apply.

Please note, NO REFUNDS will be given on any new, used, or damaged item if it is not returned in the original packaging, no matter what condition the packaging is in. If the item qualifies for free shipping, you will be charged the original shipping cost and are responsible for shipping the product back with the shipping carrier of your choice.

We must receive the item undamaged. We recommend you package it accordingly and purchase insurance for higher-priced items to ensure you receive the full refund minus any incurred fees as applicable. We reserve the right to refuse the return of accessories.

Because items are your responsibility until they reach us, we recommend that you send the parcel using a delivery service that insures you of the value of the goods. Return shipping is at the customer's cost. At Beaver Industrial Supply’s discretion, delivery charges can be refunded if the goods are defective.

Returns require a return authorization number. Please call customer service at 314-773-5999 or submit a customer service inquiry to start the exchange or return process and receive an authorization number.

Machinery too large for parcel shipment (palletized or crated) is only returnable if there is a material defect that cannot be resolved by replacing components.